Sample No. 0234
Hand-Cut Bookshelf Moulding with Hollows, Rounds and a Rabbet Plane
Shape a decorative bookshelf profile by hand, guide planes with simple rabbets and learn why one continuous length gives cleaner joints.

For this bookshelf, a hand-shaped moulding adds a clean finishing line while keeping the profile flexible enough to design with hollows and rounds. The practical lesson is just as useful: guide the planes with rabbets, refine the corners on a mitre shooting board, and make the moulding in one continuous length when the project allows.
From stone profiles to wooden details
Mouldings began as architectural features. Builders shaped stone and masonry into projecting edges and recessed channels, defining building forms and creating patterns of light and shadow. Egyptian builders used moulded details, while Greek and Roman architecture developed a broad vocabulary of profiles.
Greek forms included the torus, ovolo, cavetto and cyma. Roman builders adopted and developed these shapes further. Woodworkers later adapted the established architectural idea to timber, using carving, scraping and edged tools to create decorative details in furniture and wooden interiors. The Romans used mouldings in both settings. The precise timeline of wooden moulding is difficult to establish, but the idea itself predates woodworking.
Specialised planes made it easier to repeat a profile consistently. The maker of this bookshelf had built a complete set of moulding planes in 2017, though half a set would have been enough for the work described here. Dedicated planes can be satisfying tools to own and use, but they aren’t essential for exploring different profiles.
Choosing and preparing a profile
The maker sketched several possible profiles before settling on one. Whether those sketches came from historical examples or were original designs is unclear; all looked appealing, and the final choice came down to preference. That’s a useful approach for a one-off detail: draw a few options, compare their curves and steps, then settle on a profile that suits the piece.


To prepare the timber, the maker first cut a rabbet along its length with a rabbet plane made in 2017. A marking gauge can guide the starting cut even when the plane has no fence. The plane’s arris rests in the groove left by the gauge, helping keep the first pass on course.
Begin by widening the marked groove carefully. Keep the arris tracking inside it, then tilt the plane a little closer to vertical with each pass. Continue until the plane stands upright and the rabbet is established. Gradually changing the plane’s angle is the key: the shallow start gives the tool a track to follow.



Next, cut two smaller rabbets. These form tracks that help guide the moulding plane as it shapes the timber. Together, the rabbets provide reference surfaces for the planes to ride against, supporting a more controlled cut along the length.


Shaping curves with hollows and rounds
For the lower cove, the maker used a No. 7 round. As the plane travels along the timber, the lower half of its sole rides against the bottom rabbet. That contact guides the plane while the iron cuts the curve. The account notes that filming this operation is awkward when one hand holds the plane and the other holds the camera; the method is conveyed through the tool’s contact with the prepared track.

There’s a naming wrinkle here. Graham Blackburn describes the English term for this kind of plane as “hollow,” referring to the hollow or cove it forms. The maker uses a hollow to shape the upper part of the profile, then shows the resulting moulding.

Hollows and rounds offer many possible combinations. They let a woodworker reproduce a known profile or create a new one, without being restricted to the shapes available in dedicated moulding planes. If the same profile is used often, a dedicated plane can save time and effort; for occasional work or experimentation, hollows and rounds provide a versatile way to shape the curves.
Fit mitres and avoid profile mismatches
A mitre shooting board helps refine the angled ends of mouldings so they meet closely at the corners. Accurate mitres matter because even a well-shaped profile can look untidy if the ends don’t fit together cleanly.

Length matters too. When a moulding is made from several shorter sections, hand shaping can leave small differences between the profiles. The maker demonstrates this with two pieces that don’t match perfectly. Even if each section looks good on its own, a mismatch at the joint can interrupt the line of the finished trim.

Where the project permits, make the moulding long enough to cover the whole section in one piece. A continuous length avoids a profile change at the join and gives the bookshelf a cleaner finish. The source connects this need for long workpieces with the length of traditional benches: workbenches were often 9 or 12 feet long, and joiners’ benches were typically 12 feet because joiners handled larger pieces than furniture makers.
Once the moulding is assembled with the bookshelf, it provides the finishing detail that brings the piece together. For this project, a chosen profile, guided hand planes and careful mitres turn a length of timber into a distinctive edge.
